Bueno, tenía logic 5.2, digo tenía porque después de instalar el Ks me aparecio un mensaje de error intenté abrirlo varias veces pero nada. Hay una opción configurar audio, en la que en la pestaña driver 2, creo puedes cambiarla entre los diferentes controladores que tengas sea asio, etc. espero el ks. Estaré atento para también solucionar el problema de mi máquina.
Saludos
vaya, yo estaba por instalar los kx y uso logic 5.2... cuando tenga resultados te comunico mi experiencia.
Ahora...¿has probado de grabar con otro soft? si no lo has hecho, intentalo, así sabremos si el problema es con logic o es la config del panel kx. Tal vez Psgirl te pueda ayudar, ella tiene experiencia con los kx, revisa topics viejos que en uno de ellos ella hace una pequeña guía de config... y suerte!!!
si lo que quieres es grabar por el line in de tu tarjeta de sonido tienes que comprobar que en el panel de grabacion tiene que estar activado el AC97 y que tenga volumen. Despues en el panel de AC97 tienes que indicarle la fuente por la que quieres grabar (entrada de linea, microfono, mezcla estereo, etc...) y comprobar en este mismo panel que las opciones de linea y microfono esten activadas y con volumen.
espero que te sea de ayuda.
un saludo
todo lo que te indico es para la configuracion de los drivers kx.
gracias por los consejos, me sirvieron. espero poder compartir mis experiencias pronto.
tambien encontré esta información ila comparto:
How to set up KX drivers with Soundblaster Live 5.1 card and Cubase
The following method works for me. I am no technical whizz but I read the forums and did some trial and error and now have my setup working just fine. The following example gives one stereo input to cubase with latency as low as 2.66ms.
N.B. Once setup you will be restricted to a project sample rate of 48kHz.
1. Uninstall all soundblaster software
2. install kx drivers
3. open kx mixer by clicking on the icon on the bottom right of screen
4. select “ins n outs” . Unmute “ac97” and push the faders up. (It is unmuted when the little dot is blue).
5. select “ac97” . Press "ac97 reset" then select your source for recording (usually LineIn, or Mic). This is where you switch between different input sources to be recorded in cubase.
6. select . Here’s the tricky part! Look for a panel called “prolog” and another called “epilog”. Connect (click and drag) the first two outputs from the “prolog” to the last two inputs of “epilog”
This connects "ac 97" to the kx asio inputs 14 & 15. (14 & 15 are chosen because they work properly in stereo.)
7. Disconnect (right mouse click while over the connection) the first two prolog to router connections.
This step will prevent the problem of hearing the input signal doubled over itself in cubase.
To set up to record using line2/mic2 input (livedrive) click here
8. Close the KX Mixer. It is now set up.
9. Launch Cubase 5. Choose Options/Audio Setup/System.. (Cubase SX users choose devices/device setup../VST multitrack.) Under ASIO device choose “kx ASIO”. Press ASIO control panel and you can use the arrow up or down to change the latency. Try 5.33ms. Set Monitoring to tape type or record enable type (not global disable).
Tip: Once you have finished all recording/tracklaying and are ready to mix, switch to a higher latency. This will enable your system to handle a lot more effects, plugins, etc
10. Choose Panels/VST Inputs. (SX users choose devices/VST inputs.) Activate only kxin14 and kxin15 – deactivate any others. Choose ok if asked to remap. Save over your default setup. Enable a track for record. Load an effect. You can now record while hearing an effect and have no (very very small) delay!! VST instruments can also be played from a midi controller with the same low latency.
Go to the KX site and give them some money if you are happy. They are doing a fine job!